Contact Us

If you have any questions, you can contact us. Required fields are marked *

asphalt specification passing aashto t 164 80

Asphalt Testing Equipment - Edilab

Asphalt T esting Equipment. Bitumen Penetration Kit. ELC 518. Ref. ASTM D-5, EN - 1426, 13179-2 ... Standards - ASTM D 5, IP 49, ASTM D1321, ASTM D 2884, ASTM D1403, IP 310, BS:1377, BS:2000- (Part ... ASTM Thermometer Type 80F, Range : 395° F to 415° F ... EN 12697-1, ASTM D 2172, AASHTO T-58, T-164.

Learn More

section 401 -140 - NH.gov

2012. 5. 3. — percent of the fine aggregate blend shall pass the No. ... suitable for AASHTO T-209 when mixed with the appropriate asphalt, in order to verify the design. ... SECTION 401. -164-. 2006 NHDOT. STANDARD. SPECIFICATIONS ... When a core is less than 80% or more than 120% of the nominal thickness, ...

Learn More

CREATING A PERFORMANCE-BASED ASPHALT MIX ... - Core

9- Aggregate Gradations (Percent Passing by Dry Weight of Aggregates) . ... used to develop the Plant Mix Oil Sand Asphalt (PMOSA) Specification. ... chemical extraction method (AASHTO T 164) done by an independent laboratory, Garco ... 80. 90. 100. Percent Passing. Sieve Size (mm). (plotted on a 0.45 scale). Oil Sand ...

Learn More

401.02.22 - WV Department of Transportation - WV.gov

T 164, Quantitative Extraction of Asphalt Binder from Hot Mix Asphalt (HMA). ▫ T 166, Bulk ... MS-2 Manual, Mix Design Methods for Asphalt Concrete and Other Hot-Mix ... Stability and Flow: AASHTO T 245 or ASTM D 5581 as applicable. ... The percent passing each sieve contained in Table 401.4.2A, from one sieve larger.

Learn More

Manual of Test Procedures for Materials - Illinois Department

2017. 3. 6. — The Illinois Modifications for ASTM and AASHTO test methods and standards are available online. ... aggregates, hot mix asphalt and Portland cement concrete and soils. ... Passing Ability of Self-Consolidating Concrete by ... (Effective 03/04/80) ... Replace AASHTO Standard T 164 with the following:.

Learn More

SECTION 406 - The National Center for Pavement Preservation

AASHTO T 96 45.0% Absorption AASHTO T 19 6.0% * This value supersedes the value given in AASHTO M 195 7 406.2.2 Use lightweight aggregate that is non-corrosive and meets the gradation requirements within the ranges shown in the following table. 406.2.2 Gradation Range of Lightweight Aggregate Sieve Percent Passing, % ½-inch 100.0 ê-inch 80.0 ...

Learn More

PDF TECHNICAL DATA SHEET - Aquaphalt

• AASHTO T-304 FAA value > 45 • AASHTO T-11/ASTM C-117 % passing 75-µm (No. 200) < 7.0 • AASHTO T-27/ASTM C-136 Uniform consistency of material BINDER: The binder of - Aquaphalt® is a proprietary liquid blend that contains renewable natural raw materials. Reactive Binder is a further development of the "Raps-Asphalt" technology ...

Learn More

STANDARD CONSTRUCTION SPECIFICATIONS FOR ASPHALT

AASHTO T-164 Test for Quantitative Extraction of Bitumen* ... Construction Specifications for Asphalt Concrete, by The Asphalt Institute. ... Sieve Size Percentage Passing Sieve 1/2" 100 3/8” 90-100 #4 10-30 #8 0-8 #200 0-1 B. Stripping Test for Aggregates

Learn More

PDF DOUBLE CHIP SEAL SPECIFICATION DESCRIPTION double

Oil Distillate by Volume of Emulsion, % 3.0 AASHTO T 59 Residue, % 65 AASHTO T 59 Tests on Residue (b) Penetration, 25 oC, 100g , 5s, dmm 70 150 ASTM D 5 Solubility in Trichloroethylene, % (c) 97.5 ASTM D 2042 Toughness, in-lb 70 ASTM D 5801 Tenacity, in-lb 45 ASTM D 5801 The specification for CRS-2P is in accordance with the material ...

Learn More

Demonstration and Evaluation of SUPERPAVE Technologies

for "Verification of SHRP Asphalt Specification and Mix Design. ... Passing Gradations Recalculated Using 1974 Tolerances ... The AASHTO Subcommittee on Materials prepared specifications for use by the AASHTO ... traffic level of less than 3 million 80-kN ESALs, and Gyratory Mix Compaction of Ni = 7, ... AASHTO T-164.

Learn More